AustraliaListed, local and safe classifieds market in Australia.
States
For Sale
Real Estate
Jobs

Adams 40 steel. Great round hull. Internal fitout to complete in CLIFTON BEACH, Tasmania for sale

Adams 40 steel. Great round hull. Internal fitout to
Adams 40 steel. Great round hull. Internal fitout to
Adams 40 steel. Great round hull. Internal fitout to
Adams 40 steel. Great round hull. Internal fitout to

Beautiful round bilge steel hull from 5mm steel
Only selling following serious accident & wife wants it sold.
Centre cockpit moderate draft cruising keel (rebuilt and ballasted keel 3.3ton)
Two pot epozy interior paint
Polyurethane hull paint (additional tin if required)
Lots of stainless (needs polishing)
Steel work complete except for skeg cladding and grinding a few anchor points on deck and supports. Local welder can assist or can use my mig and tig subject to consumable cost - no gas. Many builders are pre treating rust (ie coaming, skeg, cockpit - fairly minor) and painting over with epozy mastic with great results (supplied). I have avoided this although did a test area and hasnt rusted in 8 years. Hull and interior was blasted professionally and painted immediately. Hull is adjacent to water but is very resistant to rust). Need anodes.
Deck, cockpit and engine beds need paint and joins around bow sprit, duck board and tow rail (2 pot epozy supplied). Shouldnt need professional blasting (portable blaster can do this & coaming needs same for best result, blaster may need new hose!).Needle gun will also do a good job (can use)
Cypress and Baltic pine lined interior (needs varnishing and some finishing, I think varnish supplied)
No electrics installed although some gear available (fuse board, lights, water pump, bilge pumps, manual and electric etc these are all second hand & uninspected recently)
Partially fitted, all rooms in place, bathroom fitted except toilet & shower & bits & pieces (new toilet supplied & old shower & taps included??) duragalv furniture frames and ply over and painted, floors in - not painted, windows fitted, deck hatches (5) fitted. ceiling needs lining!
Bowsprit and inner forstay boom and inner forestay post built), two chain lockers (no rust)
No stautions supplied (unless you want old ones) bases are all in place.
Requires (0r best) to instal new rudder shaft bearing (about $250) & easy to fit
Supplied with some gear (mast - original but oversize, manual anchor winch (v good), some chain, anchor,boom, rudder, prop & shaft (needs shortening for new engine), stern gland, duck board bearing, winches, steering, stove (new), water tanks, fuel tanks, fuel header tank (all painted or SS, davit(SS), pushpit & pulpit(needs polish), etc)
lots of old gear (not recently inspected or warranted) sails, rigging, mainly new lines lines.
Optional unused Nanni 50 hp engine to suit ($10,000) comes with all fittings to install (about $15K retail)
Easy to install engine on engine beds and access cover in cockpit makes gives great access.
A committed individual could put in water very quickly, 2 weeks?? (can stay in situ for 3 months or neg longer, with access to storage shed,power and some tools, portable blaster, compressor etc - can use on site Supply of screws and bolts but some some required)
While alot is done and supplied it is still a significant project to complete & you would need to be handyman or contract out- see photos. Reasonable assistance would be provided but no lifting or grinding etc (I am retired)
Sorry, Prices are not negotiable! Please no dreamers - sorry was one once!. If you cant buy please dont inquire - sorry to be blunt! Have had many inquires & hard to sort through.
This is not an urgent sale and can postpone settlement for a few months. Prices are ex my yard in Sandford Tas. Freight is buyers responsibility & large area for crane & low loader.
I have a new boat (because couldnt finish) and some gear may migrate to this - notice provided). If pictures dont load I will reattempt in few days.
May be delays in responding to phone and gum tree inquires (travelling for week)
I dearly wish I could finish the project and am still on the fence but will sell to committed uncomplicated purchaser (I think the purchaser & vender need to be compatable if buyer is working from my yard for long periods & needs fair bit of assistance). not such an issue if intend to transport immediately.